Get an Interior Painting Estimate from Colorado Painting

Get Popcorn Ceiling Removal in
Colorado Springs |
Colorado Painting 

Get a free estimate for popcorn ceiling removal here or

  Give Us a Call at (719) 224-8865

Popcorn Ceilings Are Outdated in Colorado Springs

Why Update Behind the Times Colorado Springs Popcorn Ceiling

Popcorn ceilings were the fashion in the 1970's and 1980's... hello 21st century! Possibly your house was built in the 70's or 80's and you are sicked and tired of seeing those filthy out of date ceilings. It  is just one of those "I'll get around to it" sort of tasks that you finally decided to take on. A lot of your neighbors chose to upgrade their house's appearance and at this time it's your turn. You deserve to go home to a fresh up to date appearance.

Right Way to Remove a Popcorn Ceiling With Colorado Painting

Right Way to Remove a Popcorn Ceiling With Colorado Painting

It is a sound as well as smart option to pick a company, such as Colorado Painting, that is licensed, bonded, and insured. We are specifically for popcorn ceiling removal, and all of the adjunct professional services such as residential and also commercial painting. This means we can help you irrespective of if the popcorn ceiling is outdoors, in your bedroom, in your commercial structure, or anywhere else! We take the welfare of our workers and also residents very seriously. It is a laborious, so allow Colorado Painting help you and also avoid the stress and danger or the danger and also expense of some contractor not being ready!

DIY Popcorn Ceiling Removal Is Difficult

Reasons Why Removing Popcorn Ceilings is Difficult

Getting rid of popcorn from your ceilings is a straightforward job, and some individuals decide to do it on their own. It can be a untidy laborious task, in addition to it's unclean as well as time consuming. This is why your buddies and also neighbors decided to purchase a specialist popcorn removal contractor to finish the job, saving you stress, time and mess.

The professionals at Colorado Painting do the whole project starting from eliminating the old texture, putting on the new texture and finishing it off with a flawless coat of paint. When you see the transformation in your ceilings, you'll rejoice you made the best decision; as will other people in your home!

Easily Improve the Style of your Ceiling

Easily Improve the Style of a Ceiling

Popcorn ceilings were applied mainly because it was a cheap means to swiftly spray on a ceiling to cover problems and errors in the condition versus the attention to detail necessitated for a quality paint job. However, it is more challenging to clean up and also is not really resilient resulting in it typically turning into an eyesore or damaged. They are difficult to redo or overhaul, yet Colorado Painting is up to the job as well as can help give your space a brand-new style.

Our specialized crews have all the tools required to get rid of the popcorn ceiling to help keep themselves and your living area risk-free. It is frequently less expensive to hire a company such as Colorado Painting as opposed to purchasing every one of the tools on your own. Additionally, it will certainly be done right the first time without harm to your ceiling or other areas and the worry of finding out the hard way what errors in getting rid of a popcorn ceiling can lead to. Take the crud of a popcorn ceiling right into a contemporary tidy style in a secure as well as timely way with Colorado Painting!

Other Colorado Springs Services

Find General Contractor in Colorado Springs

Get help with a renovation project

Location: 5883 N Academy Blvd, Colorado Springs, CO 80918

Rating:
4.50

Categories: Remodeler

HOMEfix provides award-winning home remodeling in Colorado Springs, as well as repair and roofing services. Improve your home. Request a free estimate today.

Location: Google Map

Rating:
4.60

Categories: General contractor

J&J construction is home of the Build Your Own Basement® program where Colorado Springs homeowners can save up to 40% on basement finishing projects.

Location: 111 S Tejon St # 112, Colorado Springs, CO 80903

Rating:
3.90

Categories: General contractor

Colarelli Construction is a general contracting and construction management company located out of Colorado Springs, Colorado.

Find An Electrician in Colorado Springs

Leave electrical repairs and installations to the professionals

Location: 2345 Academy Pl #222, Colorado Springs, CO 80909

Rating:
5.00

Categories: Electrician

Swartz Electric is a residential & commercial electrician specializing in emergency electrical repair, lighting design and installation, electrical panel upgrades, and more. Serving clients across Colorado Springs, Fountain, Falcon, Peyton, Old Colorado City, Green Mountain Falls, and surrounding CO communities.

Location: 5855 N Academy Blvd #255, Colorado Springs, CO 80918

Rating:
3.70

Categories: Electrician

With over 35 years of experience as electricians in Colorado Springs, you can trust Gaddie Electric to help you find the best electrical contractor for any job!

Location: 4740 Forge Rd #106, Colorado Springs, CO 80907

Rating:
4.90

Categories: Electrician

Need repair or maintenance for your home or looking to remodel? Call the Electricians at Front Range Electric, Inc. Contact us for a free consultation!

Location: 3431 N Prospect St, Colorado Springs, CO 80907

Rating:
5.00

Categories: Electrician

The Electric Way offers personalized residential and commercial electrical services. We strive to provide the highest quality service that is done right the first time. Hire the best electrician in Colorado Springs today!

Find Blinds in Colorado Springs

Wondering how to choose the perfect window treatments?

Location: Google Map

Rating:
4.60

Categories: Blinds shop

Budget Blinds of Southeast Colorado Springs, CO brings the showroom to you, accurately measures your windows, and installs your blinds, shades, shutters, and much more.

Location: Appointment Only, 12440 Tex Tan Rd, Peyton, CO 80831

Rating:
5.00

Categories: Window treatment store

Quality and Affordable Custom Colorado Springs Blinds & Shutters. We adjust to your Interior Design. Order Today and Get Installation Within 8 Days.

Location: Google Map

Rating:
5.00

Categories: Window treatment store

Quality and Affordable Custom Colorado Springs Blinds & Shutters. We adjust to your Interior Design. Order Today and Get Installation Within 8 Days.

Location: 5 E Bijou St #189, Colorado Springs, CO 80903

Rating:
5.00

Categories: Window treatment store

Colorado Springs Shutters is a Colorado Springs shutter company that offers wood blinds, roman shades, plantation shutters and window treatments.

Find Home Lighting in Colorado Springs

Shop for modern lighting, lamps and fans

Location: 7120 N Academy Blvd, Colorado Springs, CO 80920

Rating:
4.00

Categories: Home improvement store

Chain home improvement retailer for tools, appliances & other products (some offer truck rentals).

Save time on your trip to the Home Depot by scheduling your order with buy online pick up in store or schedule a delivery directly from your Academy Blvd store in Colorado Springs, CO.

Location: 2250 Southgate Rd, Colorado Springs, CO 80906

Rating:
4.00

Categories: Home improvement store

Chain home improvement retailer for tools, appliances & other products (some offer truck rentals).

Save time on your trip to the Home Depot by scheduling your order with buy online pick up in store or schedule a delivery directly from your Sw Colorado Springs store in Colorado Springs, CO.

Location: 6380 Corporate Centre Cir, Colorado Springs, CO 80919

Rating:
4.40

Categories: Home improvement store

Whether you’re decorating a single room or designing an entire home, we’ve got you covered, from floor to ceiling.

Location: Cascade, CO 80809

Categories: Antique store

Buy a domain and see how a premium domain can be the best investment. Your business starts here. Buy a domain today.

Nearby Cities

Zipcodes Near Colorado Springs, CO We Service

80806
80901
80902
80903
80904
80906
80907
80909
80910
80917
80918
80905
80915
80916

Colorado Springs Comments

Robert Chickey
User Description: Owner/Builder (1988-present)
Posted on: Nov. 19, 2017, 6:23 p.m.
Castle Rock, CO
Just how much do bathroom renovations cost?
Mickey Curran
User Description: 25 years construction experience, gen. Contractor, renovator, licensed
Posted on: June 10, 2018, 2:23 a.m.
Broomfield, CO
The national average price of bathroom remodeling ranges someplace within $5,949 - $14,814. The purchase price of bathroom renovation that is moderate may be somewhere around $2,500, though this price can go as high as $25,000 to get a high-end toilet renovation job that is large.
Ednamae Smith
User Description: works at Decorative Painting
Posted on: Sept. 24, 2019, 6:48 p.m.
Colorado Springs, CO
Depends a good deal on how the renovation is, how labour intensive the approach, and also how high priced the fixtures are is. If used to do it, for a toilet, brand new floors, paint, and also a lavatory faucet, it would cost $500 -- 700 for approximately $600 labor and stuff . A one or two day undertaking. That is a redesign, but would still freshen up the room. For brand fixtures, more, redo the shingles, alter a number of electric and the plumbing, tons of tile and also gut the room, it might run . Just take more such as two or per week. That's still an average bathroom--nothing that elaborate or large. Wherever I live, '' I can perform all of the task without having to telephone. Another variable would be speed. There are larger organizations that specialize in one day remodels using a fancy warranty, etc.. I've heard of individuals giving 6000 for a shower to them. Sounds dismissive to me, however people enjoy. The amount tag on labor in your field makes a distinction. I am fairly expensive in the rural place in which I dwell, but I'm guessing in some regions the work could be considerably more expensive, especially in the event that you've got to find yourself a succession of tradesmen in.
Jorge Barton
Posted on: Sept. 19, 2019, 4:16 p.m.
Colorado Springs, CO
A tool was called'Remodeling Calculator' at which you are able to estimate the cost of any type of renovation your home needs. But if You're Looking to estimate the price of the toilet, here is the link into this instrument Rest Room Remodel Expense In the event you would like to understand just how to gauge the amount being spent on bathroom renovation? Browse the content under to find a fundamental notion. How to Estimate the Price of a Toilet remodelling Hope this can help Joyful renovating!
Rajaswi Kori
Posted on: Aug. 27, 2018, 10:06 a.m.
Woodland Park, CO
House owners have many choices once they redesign the entire cost and also your bathroom depends on price range and personality. Remodels offer some of the peak re sale returns as a house improvement project. It is take a long time to finish, so it is essential to assemble and plan your bathroom remodeling ideas ahead of time and find the suitable remodeling contractor to the career. Asking concerns, setting expectations, budgeting and cost quotes out of the start can indicate that the distinction between finding and relish dealing with a lengthy few weeks and stressful.
Eric Elford
User Description: former Whorehouse Piano Player (1979-1993)
Posted on: Oct. 23, 2018, 5:38 a.m.
Manitou Springs, CO
While this Is an Excellent question, like Several answers below are doing a disservice, it seems, ... since technically, they are completely incorrect. Why is this? Effectively, pricing virtually any building job greatly is determined by a whole bunch of Unique factors: The location of the project, since there is a difference between California LosAngeles and Chicken, Alaska. The size of this bath, while it can be some 500 sq foot bathroom in a Richmond mansion or really actually a 20 square foot bath in a Manhattan loft. The intricacy of the undertaking, because no 2 homeowners will have the exact vision for the Bath-room - antique countertops / pastoral mirrors / etc.. The timeframe in the homeowner desires it all done. Some contractors might be more economical but be booked for that following calendar year. The standard & standing of this contractor's business. It costs to get the reassurance of mind an expert will do this correctly. ... wait, so how can I figure out the cost of your bathroom remodel? You certainly can do this by doing work backward! Figure out the scope of the bathroom remodel endeavor and estimate how much time it will take you ( it is Far Better to slightly more than underestimate because you are going to wind up losing cash ) Figure out how many workers you'll have to bring along with you. Find out the amount of cash you want to earn, per hour, to cover yourself and your staff. Variable in the expense of material together with traveling to and from the work website. Factor in organization and marketing expenses based how many jobs you do at your costs of running your business and a year. If, for example, you do 20 tasks like that each calendar year this job should cover 1/20 of one's small business expenditures. And there you proceed, you recognize exactly how much you need to charge to stay worthwhile! P.S - This helps with favorable builders from neighboring locations, not your ceremony area compared not compete with one another, but ones that you are able to share pricing together and receive yourself a very superior notion of projected charges. Fantastic fortune in pricing your future bathroom remodeling project and also expect this really helps! Best wishes from ContractorStudios,
Matt McKeon
User Description: studied Interior Design (2000)
Posted on: April 18, 2018, 6:57 a.m.
Colorado Springs, CO
Just how do I set up drywall on a ceiling?
Andreas Thomson
User Description: Landlord (2008-present)
Posted on: May 17, 2019, 8:36 a.m.
Fountain, CO
You need a couple of people with lengthy arms or ladders, or a drywall lifter device. Plus you require to properly screw them on with drywall screws. Appropriate factor to consider must be given to make certain fireproofing demands, electric boxes and also challenges which must not be penetrated like water lines, electrical cables, pipes and so on . If soundproofing is called for, zbar or RezBar, goop or fireproofing caulking should be taken into consideration well in advance.
Rahul Kapoor
Posted on: Sept. 21, 2019, 12:29 a.m.
Castle Rock, CO
Order a 2x4. Cut it in half. Cut one of the halves in half once again. Toenail the larger fifty percent to a full 2x4 (creating a T) as well as utilize the smaller fifty percents to brace the T so it's stiff and also sturdy. Hoist the Sheetrock over your head as well as "wedge" the T into setting on the side opposite the one you're holding. The T violates the Sheetrock not the flooring. Hold the Sheetrock with one hand as well as drill with you're freedom. This entire procedure will be less than pleasant. However you'll master it as well as at some point obtain your work done (you'll be sore as hell by the end of it also). For wall surfaces I utilized a hoe to lift/wedge the GWB against the wall surface from the bottom (type of like a crowbar). Again still with 1 hand while holding the sheet with the other. A magnetic drill bit is a MUST. A device belt helps. A light cordless will save your shoulder (as opposed to a heavier cordless, this would certainly be impossible with a cable). Good luck!
John Whitehead
Posted on: Sept. 6, 2019, 1:33 p.m.
Federal Heights, CO
if you are mosting likely to attempt this by yourself the supply store need to have a tool utilized to stand up drywall sheets for while you screw them or toenail them down. i would certainly likewise check with your local building division to find out about drywall installment building ordinance requirements. You will need to get a license as well as have a toenailing inspection prior to you secure all of the joints with compound as well as joint tape yet prior to that you may likewise require and electrical examination too or even a pipes assessment. You might even need an energy calculation given by a power engineer.
Asokan Krishnaswamy
User Description: studied at National Public School, Koramangala
Posted on: Sept. 2, 2019, 5:35 a.m.
Castle Rock, CO
As an individual that grew up using building sites I really feel secure in claiming that the very best way to hang drywall is to call a pro. The listing of what I can do is fairly long. The checklist of what I will certainly do gets shorter every day. The very first thing I put on my checklist of what I won't do was drywall. Other than spot a hole in a place that will not reveal drywall is finest delegated the pros. It looks easy, however if not done properly it appears like "ca ca". As a Real estate professional I see Do It Yourself drywall projects commonly as well as absolutely nothing attracts down the worth of a residence quicker than an inadequately done drywall job.
Luke Bergschneider
User Description: former Home Improvement Writer
Posted on: Aug. 3, 2019, 8:54 a.m.
Brighton, CO
I Have a video revealing The Very Best AND ALSO SAFEST way to do it. I would very suggest NOT attempting the t bar technique, as even with help, drywall is EXTREMELY heavy and unpleasant to deal with for amateurs, and you can get hurt, harm your home or even worse. A panel lift like in this video can be rented EXTREMELY economically, and will make it a lot easier. I hung and finished new drywall for 15 years and also another 15 doing repair services and small work, as well as the lift above is exactly how I do it alone.
Penny Carlisle
User Description: MBA The Internet & Visiting and Travel, University of Delhi (2010)
Posted on: Aug. 3, 2017, 6:30 p.m.
Arvada, CO
For how long do I need to wait to paint over the interior paint on a wall surface once again?
Mickey Curran
User Description: Sub Contractors (Ext/ Int) Residential and Commercial
Posted on: Dec. 6, 2018, 6:06 a.m.
Woodland Park, CO
The minimum delay is approximately four hours, although if you intend to play it risk-free, you can quickly wait a day as well as permit the paint to end up being completely accommodated to the wall it just made contact with. Or else you're just waiting on the paint to dry. If you remain in a rush, followers and also vents can assist, yet it's still best to wait the minimum 4 hours before applying another layer of paint.
Aaron Lassig
User Description: M Tech (Roorkee Univ.) Civil Engineering, Veer Surendra Sai University of Technology, Burla (1979)
Posted on: Oct. 18, 2017, 3:40 a.m.
Pueblo, CO
What's the best way to decorate cabinets that are black?
PGN Property Management
User Description: former Yacht Refinisher (1982-2008)
Posted on: April 12, 2019, 4:18 p.m.
Castle Rock, CO
Chalkpaint the framed pieces (should you have) Americana creates a line, sold in Micheals, or order on line substantially cheaper than Anne Sloan and moves quite a distance they make a minimum of three different antique colors and after that use the wax coating for ultimate finish. Buy fresh hardware and use the chalk paint onto the hardware. ( I have had great consequences on harware utilizing chalk ending and gloomy Sandpaper, ). Chalk paint isn't hard to work with, very easy and also durable on almost any substratewash down also. THE previous WAX action SKIPS, takes some elbow grease but well worth the last results!!!!!
Debbie Todd
User Description: have mixed paint hundreds of times
Posted on: Nov. 22, 2018, 9:41 a.m.
Colorado Springs, CO
To begin with, try and take out the paint. Make use of a primer to cover the shameful shade. Normally, you can take help from specialist painters they will surely have a better answer.
Colourwalls
User Description: Held executive level positions with decorative paint companies.
Posted on: Sept. 19, 2019, 6:24 a.m.
Aurora, CO
There are tons of instructions on the internet. Paint black like any additional coloration. Perhaps two coats of primer employ a primer that's a blocker, or to either hide both the black.
Joie Mojica
User Description: Owner at Mr Handyman of North Central San Antonio (2016-present)
Posted on: June 15, 2018, 4:20 p.m.
Canon City, CO
My close companion, lacque, lacquer. Nothing beats lacquer. There is an item called RUD, find it at Kelley Moore. It is a drinking water base product or service plus it is awesome! But, it must be sprayed. In the event you'd like to roll up and brush it, then I would use a petroleum base primer. Benjamin Moore comes with a cabinet paint that is wonderful. However, be sure to prep great. Allow me to use dish soap, off the grease cuts on on. TSP can be ideal for cleaning.
Bae Ness
User Description: 55 years in fine woodworking and finishing
Posted on: Sept. 3, 2018, 8:14 a.m.
Salida, CO
You are able to both strip the paint by carrying them out and getting rid of drawers and the doors. The facial skin framework will need to become eliminated inplace till you can see how it's secured. The other solution is understand is touse the best paint and primer you can come across. It is going to still require a few coats to cover both the black. I'd sand to roughen the paint thus that the primer sticks , if painting.
Michele Taber
Posted on: May 25, 2017, 4:30 a.m.
Superior, CO
What are necessary things to try to find when acquiring indoor paint?
Adam Turner
User Description: have mixed paint hundreds of times
Posted on: July 13, 2018, 2 a.m.
Arvada, CO
First of all determine the top quality you are seeking. What is the length of serviceable use you yearn for the paint to suit? Is this a repaint for an apartment or condo? If do, a lower quality of paint is proper. If it's your individual residence and you want a gorgeous as well as resilient outcome that's a various discussion. The far better quality of the resin amounts to the capability to achieve a richer shade as well as have an even more durable surface area. I am not a follower of using any kind of various other sheen than matte for walls and below is why. If you acquire near the top degree of product available will certainly allow for a more regular saturation of shade in addition to longevity. An eggshell or greater sheen is difficult to detect repair work without seeing. A matte luster is virtually imperceptible. A high quality paint will put on also or perhaps much better than a mid level eggshell shine paint.
Isabella Smith
User Description: If it can be sprayed and called paint or finish I've used it
Posted on: Aug. 10, 2019, 10:11 p.m.
Fountain, CO
To simply advertisement something to the already outstanding answers. Washability of the paint, specifically where kids and also, probably, pets might leave marks on the walls.
Kuo Ying Chieh
User Description: Have worked, made my living with, and heated with wood for decades.
Posted on: April 2, 2019, 4:42 a.m.
Canon City, CO
What else do cupboard manufacturers make, besides cabinets?
Scott Welch
User Description: I design, build and install custom cabinetry.
Posted on: June 3, 2019, 1:38 a.m.
Federal Heights, CO
Generally cupboard makers can develop whatever you want out of wood. In my case, it's easier to note the wooden things I will certainly not build as they are much much better done by professionals. Pre-fabricated structural trusses. Musical instruments. Airplane frameworks. Upholstered chairs. Tennis noises, archery bows or most other showing off tools. Nevertheless; a cabinet maker can quickly make a desk and table to match your display case after that upgrade all the door and also home window trim in the room to match additionally.
Barry Croker
User Description: Amateur woodworker.
Posted on: Sept. 2, 2019, 11:36 p.m.
Canon City, CO
The majority of my earnings originates from cabinets. Periodically I get require a custom piece of furniture. Maybe it is just a bench or something to match their cabinets or maybe something unique like bunk beds with a full size mattress up top as well as a queen on bottom. I've obtained ask for dungeon furnishings (" we want a bed we can turn from without breaking it".) I have actually replicated an antique bed, the consumer had an antique bed and wanted an additional so both kids could have matching beds. I've done some repair work and refinishing. I've laminated curved handrails for a balcony and also curved window trim, once I also changed a wooden handle on a tea pot for a consumer. I've made repair work components to patch wood columns as well as I have actually made weird items of molding to match the existing trim in an old home. I have actually made shop counters, consisting of some curved ones. One that enters your mind was for a gelato shop with really loud paint colors, I'm keeping in mind pink, green, and yellow on the very same counter. Once I developed a 5 ′ size Mahogany planter to go in the lobby of an office building (the base was rounded, the top was rounded, as well as in between were 12 raised panels). The business's factory built a stainless steel lining as well as handled to damage the wood while installing it. I ended up having to do some repair work onsite before the tree it was expected to hold was grown.
Mark Farver
User Description: Decades of experience painting homes
Posted on: Aug. 17, 2019, 1:20 a.m.
Federal Heights, CO
Thanks for the A2A. I am a closet maker. I no longer stand at a bench all day and make quite things out of timber, having actually been taken into the office for a Project Supervisor's job; yet I am still certified to make closets and, actually, my old bench in the shop still stands empty, with my device box still resting there simply in situation:--RRB-. The term "cabinetmaker," these days, truly suggests "highly proficient woodworker." There are extremely few points you can construct of wood a cabinetmaker can't construct. I built all the furniture in my residence, as an example, plus it has custom-made moldings and also doors and so forth. The business I currently help focuses on store fixtures. These run from fancy woodwork in natural hardwoods (think Starbucks) to simple Jane practical (believe checkout counter in a convenience store.) That fancy, bent check-in counter with the rock top as well as solidified glass privacy displays at your medical professional's office? I construct those. That ornate carved bar at your regional bar? I develop those. That fancy-Dan ceiling component hanging over your head in the 4-star dining establishment; resembles a Wright bros biplane had a head-on with a picket fencing? I build those. (Those in fact offer a helpful objective, in instance you really did not understand. It's a sound baffle; cuts the noise from other restaurants. That's why you see them all over.). My company could do other things utilizing the very same individuals and also devices; we could run millwork (believe moldings like wall or door casing); we could make sash and door; we can develop kitchen cabinets and also bath vanities as well as garage workbenches and just about anything else you can envision. We don't; we're not in that organisation. Yet we could, conveniently. There are things I do not presently have the skill to construct:. I am not a luthier; I do not understand exactly how to make hollow-body guitars or violins. I don't loft space wooden-frame watercrafts or planes. I don't construct unibody wood hull canoes. I don't transform baseball bats or golf club heads. I can most likely learn how to do any of that, however I do not have any kind of experience as well as, in most cases, don't own the tools. It's simply not my job. However I have built a great deal of points you don't think of as "closets." I have developed a great deal of trade convention displays, and also the pet crates that carry them around. I developed high accuracy concrete forms for some time; primarily modular so they can be removed as well as recycled. I once built a workdesk assembly for a radio terminal, back when DJs actually rotated vinyl records. It had two holes in it where the turntables go, and also no framework underneath, since they rested on solid concrete columns linked to the structure foundation so they didn't get resonance. I have develop houses and also barns and also fencings and on and on and also on. Primarily, if it's timber, I can make it.
Adrian Bew
User Description: Writer, widow, mother, traveler.
Posted on: Sept. 21, 2019, 9:09 a.m.
Salida, CO
Cabinet maker, is rather of a broad term. It implies they only make cupboards. Nevertheless a cupboard manufacturer is really an experienced timber worker. They can general make anything you need out of wood.
Bonnie Shoemaker
User Description: Painting contractor 30 years
Posted on: May 11, 2019, 2:41 p.m.
Fountain, CO
Money, taking into consideration those are the only men who I typically see rocking a tape measure that reads in 1/32nds like it's nothing. It's difficult enough to train some guys to review in 1/8ths often. However yes, I'm opting for cash on this.